Autor Wątek: Gotek z wyświetlaczem , plik ff.cfg  (Przeczytany 2377 razy)

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Gotek z wyświetlaczem , plik ff.cfg
« dnia: 2023.03.07, 20:25:02 »
Dzień dobry,

Wiecie może jak zrobić aby nazwa pliku się przewijała gdy jest za długa?

Gotek z wyświetlaczem 

damik

  • Fresh rosin sniffer ;)
  • *****
  • Wiadomości: 2426
  • Miejsce pobytu:
    Generalnie Polska, głównie Bytom czasem Bielsko-Biała oraz okolice
  • ZX'owy i nie tylko...
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #1 dnia: 2023.03.07, 23:01:07 »
Zwykle to się długa nazwa przewijała domyślnie na standardowych ustawieniach z OLED, ale nie wiem jak teraz jest po update'ach i na innych wyświetlaczach.
« Ostatnia zmiana: 2023.03.07, 23:10:47 wysłana przez damik »
Wszystkiego po trochu: Schwarz, mydło i powidło... konsole, stare i nieco nowsze komputery oraz akcesoria i duperele.

KWF

  • *****
  • Wiadomości: 6823
  • Miejsce pobytu:
    trzecia planeta od Słońca
  • "I co ja robię tu, u-u, co Ty tutaj robisz ..."
    • Insta do lasownia
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #2 dnia: 2023.03.08, 07:36:57 »
Z FlashFloppy Wiki FF.CFG Configuration File opcje:

Cytuj
display-scroll-rate = 100-65535 (200*)
   LCD/OLED long filename scroll rate (ms per update)
   Larger value means slower scroll

display-scroll-pause = 0-65535 (2000*)
   LCD/OLED long filename scroll start/end pause (ms)
   N=0: Endless looping scroll

nav-scroll-rate = 0-65535 (80*)
   LCD/OLED long filename scroll rate during navigation (ms per update)

nav-scroll-pause = 0-65535 (300*)
   LCD/OLED long filename pause before scroll starts during navigation (ms)
KWF
-----
R Tape loading error 0:1
Moje zabawki: https://github.com/McKlaud76

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #3 dnia: 2023.03.08, 17:57:40 »
Niestety , konfiguracja wpisana jak poniżej i nic , nazwa pliku stoi jak wryta :(

damik

  • Fresh rosin sniffer ;)
  • *****
  • Wiadomości: 2426
  • Miejsce pobytu:
    Generalnie Polska, głównie Bytom czasem Bielsko-Biała oraz okolice
  • ZX'owy i nie tylko...
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #4 dnia: 2023.03.08, 18:02:32 »
To może zrób jeszcze update firmware z pendrive.
Wszystkiego po trochu: Schwarz, mydło i powidło... konsole, stare i nieco nowsze komputery oraz akcesoria i duperele.

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #5 dnia: 2023.03.08, 19:01:21 »
Wykonałem aktualizację z 3.38 do 3.39 , nadal nic :(

Maryjan

  • *****
  • Wiadomości: 6650
  • Miejsce pobytu:
    Skarżysko-Kam.
  • Scotch whiskey and West Highland Terrier
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #6 dnia: 2023.03.08, 19:29:13 »
Jakie atrybuty ma plik FF.CFG ?
Bo może tu leży problem.
"Co miałem powiedzieć - przeczytałem..." Nikodem Dyzma

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #7 dnia: 2023.03.08, 19:46:34 »
Brak atrybutów

skoti

  • *****
  • Wiadomości: 749
  • Miejsce pobytu:
    Polska
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #8 dnia: 2023.03.08, 20:31:05 »
Może coś głupiego siedzi we flashu goteka. Spróbuj factory reset. Przy wyjętym pendrive przytrzymaj NEXT i PREV przez 3 sekundy.

Waldek

  • ***
  • Wiadomości: 156
  • Miejsce pobytu:
    Łużyce
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #9 dnia: 2023.03.08, 21:38:41 »
A z ilu liter składa się nazwa pliku?
Proszę załącz tutaj plik FF.CFG, aby łatwiej było go ocenić.
Ja też miałem problemy na początku, bo wybrałem zły wyświetlacz.

damik

  • Fresh rosin sniffer ;)
  • *****
  • Wiadomości: 2426
  • Miejsce pobytu:
    Generalnie Polska, głównie Bytom czasem Bielsko-Biała oraz okolice
  • ZX'owy i nie tylko...
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #10 dnia: 2023.03.08, 21:50:51 »
Nie wiem czy czasem ten scroll się nie wywala z powodu jakiś dziwnych znaków w nazwach plików na Pendrive.
Jaki filesystem ma ten Pendrive FAT, FAT32, exFAT ?
Napisz też jaki masz tam dokładnie wyświetlacz w tym Goteku.
« Ostatnia zmiana: 2023.03.08, 21:57:56 wysłana przez damik »
Wszystkiego po trochu: Schwarz, mydło i powidło... konsole, stare i nieco nowsze komputery oraz akcesoria i duperele.

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #11 dnia: 2023.03.08, 22:00:38 »
plik ff
## FF.CFG: Example FlashFloppy Configuration File

# Place in the root folder or FF/ subfolder of your USB drive.
# NOTE: If FF/ exists, IMG.CFG must reside there, not the root folder.

# Uncommented lines below are the default settings.
# Uncommented options cannot be overridden by settings in other config files.

##
## DRIVE EMULATION

# Floppy-drive interface mode (interface pins 2 and 34)
# jc: Specified by jumper JC (open: shugart, closed: ibmpc)
# shugart: P2=DSKCHG, P34=RDY (Amiga, Atari ST, many others)
# ibmpc: P2=unused, P34=DSKCHG (IBM PC interface)
# ibmpc-hdout: P2=HD_OUT, P34=DSKCHG (not generally needed: prefer 'ibmpc')
# jppc: P2=unused, P34=RDY (Japanese PC standard)
# jppc-hdout: P2=HD_OUT, P34=RDY (Japanese PC alternate: prefer 'jppc')
# akai-s950: Legacy alias of 'jppc-hdout', previously used for Akai S950
# amiga: P2=DSKCHG, P34=DRIVE_ID (not generally needed: prefer 'shugart')
interface = jc

# Host platform: Improves image-format detection for generic types such as IMG
# acorn: Acorn ADFS
# akai: Akai (S01, S20, S950), Korg, SC Prophet 3000
# casio: Casio (FZ-1)
# dec: DEC (RX33, RX50)
# ensoniq: Ensoniq (ASR, TS, etc)
# fluke: Fluke 9100
# gem: General Music (S2, S3)
# ibm-3174: IBM 3174 Establishment Controller
# kaypro: Kaypro
# memotech: Memotech
# msx: MSX
# nascom: Nascom
# pc98: NEC PC-98
# pc-dos: PC DOS Format (geometry determined from Bios Parameter Block)
# tandy-coco: Tandy Color Computer (CoCo)
# ti99: TI-99/4A
# uknc: UKNC / DVK Soviet PDP-11
# unspecified: Common default geometries (including IBM PC)
host = unspecified

# Pins 2 & 34 output (drive->host) manual configuration
# auto: Auto-configure from interface= setting
# nc: Unused/No Connection [eg. if pin is an input (host->drive) on your host]
# low: Always 0 volts (0v)
# high: Always 5 volts (5v)
# rdy: Drive ready (Ready = 0v)
# nrdy: Logical complement of above
# dens: Density mode (High Density = 0v)
# ndens: Logical complement of above
# chg: Disk changed (Changed = 0v)
# nchg: Logical complement of above
# Values: auto, nc, low, high, rdy, nrdy, dens, ndens, chg, nchg
pin02 = auto
pin34 = auto

# Forcibly write-protect images, or respect the FAT read-only attribute?
# Values: yes | no
write-protect = no

# Filter glitches in the SIDE-select signal shorter than N microseconds
# Values: 0 <= N <= 255
side-select-glitch-filter = 0

# Rotational offset of disk after a track change
# instant: No rotation during track change
# realtime: Emulate rotation of disk while track is changing
# Values: instant | realtime
track-change = instant

# Rotational offset of disk after draining a write to Flash
# instant: No rotation
# realtime: Disk rotates in real time during drain
# eot: Disk rotates to (near) end of track
# Values: instant | realtime | eot
write-drain = instant

# Index pulses suppressed when RDATA and WDATA inactive?
# Values: yes | no
index-suppression = yes

# Milliseconds from head-step start to RDATA active.
# Values: 0 <= N <= 255
head-settle-ms = 12

# Milliseconds delay from motor-on to drive ready.
# On a standard unmodified Gotek the motor signal is not connected and a
# non-default value here will have no effect. Most systems and software do
# not care about correct motor behaviour, and default (ignore) works fine.
# Values: ignore | 0 <= N <= 1000
motor-delay = 200

# What causes the disk-change (chg) signal to reset after disk insertion?
# step: Step command received
# pa14: CHGRST (pin 1 on old Sony drives), connected to PA14 (JTCK/SWCLK)
# delay-N: Automatically after N*0.5sec (0 <= N <= 15)
chgrst = step

##
## STARTUP / INITIALISATION

# Disk image loaded or ejected at startup?
# Values: yes | no
ejected-on-startup = no

# Which image (or folder) is selected at startup?
# last: Last-selected item at power-off (recorded in IMAGE_A.CFG)
# static: Static path specified in INIT_A.CFG
# init: First item in root folder
# Values: last | static | init
image-on-startup = last

# Time in milliseconds to attempt to probe attached display.
# You may set this to 0 if you have a 2-digit LED display attached.
# Values: 0 <= N <= 65535
display-probe-ms = 3000

##
## IMAGE NAVIGATION

# Auto-select the current file after N seconds
# N=0: disable auto-select
# Values: 0 <= N <= 255
autoselect-file-secs = 2

# Auto-select the current folder after N seconds
# N=0: disable auto-select
# Values: 0 <= N <= 255
autoselect-folder-secs = 2

# Sorting of folder entries in native navigation mode.
# always: Always sort folder entries. Large folders may be truncated.
# never: Never sort folder entries, instead presenting them in FAT order.
# small: Only sort folders which are small enough to sort in full.
# Values: always | never | small
folder-sort = always

# Priority of files vs subfolders when sorting folder entries:
# folders: Folders listed before files
# files: Files listed before folders
# none: Files and folders are not differentiated
# Values: folders | files | none
sort-priority = folders

# Navigation mode for selecting images/slots
# native:  Navigate through all valid images/dirs
# indexed: Navigate through DSKA0000, DSKA0001, ...
# default: native unless overridden by HxC-compat-mode config
nav-mode = default

# When navigating slots or folder, loop at min/max?
# Values: yes | no
nav-loop = yes

# Actions of first two buttons.
#              B1     | B2     | Both
# zero:        Prev   | Next   | Slot 0
# eject:       Prev   | Next   | Eject/Insert
# htu:         +10    | +1     | +100
# rotary:      Up-dir | Select/Eject/Insert | -
# rotary-fast: Prev   | Next   | Up-dir [Prev/Next are accelerated]
# reverse:     Reverse sense of B1 and B2
# Multiple values can be separated by commas, eg twobutton-action=eject,reverse
twobutton-action = eject

# Input sensor type at the rotary-encoder inputs (pins PC10 and PC11):
#  [full | half | quarter]:
#    Rotary encoder, identified by fraction of a Gray-code cycle performed
#    per detent/click. If default value ('full') requires multiple
#    clicks/detents to move position then change to 'half' (if 2 clicks
#    per move) or 'quarter' (if 4 clicks).
#  [trackball]:
#    Blackberry-style trackball (eg. using Hall-effect sensors).
#  [buttons]:
#    Push-to-ground Prev/Next buttons.
#  [reverse]:
#    If the input is working in reverse, use this option to swap directions.
#  [v2]:
#    Use the rotary encoder logic from FlashFloppy v2.x. Use this if the
#    v3 logic is too strict and results in no, or missing, movements.
# Multiple values can be separated by commas, eg rotary=quarter,reverse
# Values: none | quarter | half | full | trackball | buttons | reverse | v2
rotary = full

# Prefix for image names in indexed navigation mode. String can be empty ("").
indexed-prefix = "DSKA"

##
## DISPLAY

# Display Type.
# auto: Auto-detect (7-seg LED, LCD, OLED)
# lcd-CCxRR: CCxRR backlit LCD with I2C backpack (16<=CC<=40, 02<=RR<=04)
# oled-128xNN: 128xNN I2C OLED (NN = 32 | 64)
#  -rotate:     OLED view is rotated 180 degrees
#  -narrow[er]: OLED view is restricted to Gotek display cutout
#               (-narrow: 18 chars; -narrower: 16 chars)
#  -inverse:    Inverse/reverse video (black text on white background)
#  -ztech:      ZHONGJY_TECH 2.23" 128x32 SSD1305 OLED display
# Values: auto | lcd-CCxRR | oled-128xNN[-rotate][-narrow[er]]...
display-type = auto

# OLED Font. Narrow and wide options.
# Narrower 6x13 font permits:
#  - More characters per row
#  - Use of Gotek display cutout (eg. "display-type=oled-128x32-narrow")
# Values: 6x13 | 8x16
oled-font = 6x13

# OLED contrast/brightness.
# Values: 0 <= N <= 255
oled-contrast = 143

# Text height and arrangement on LCD/OLED
# 'default', or a comma-separated list (one entry per LCD/OLED row, top down).
# Each list item is a digit plus optional height specifier: <content-row>[d]
#  content-row: '0-3' = specified content row, '7' = blank
#    0: Current image name
#    1: Status
#    2: Image/Volume info
#    3: Current subfolder name
#  height specifier: 'd' = double height (32px, OLED only; ignored for LCD)
# 'default' depends on display, eg.: oled-128x32='0,1' ; oled-128x64='3,0d,1'
# Values: [0-7][d] | default
display-order = default

# Turn an LCD or OLED display off after N seconds of inactivity
# N=0: always off; N=255: always on
# Values: 0 <= N <= 255
display-off-secs = 255

# Switch on LCD/OLED display when there is drive activity?
# yes: Trigger on track changes and disk writes
# sel: Trigger on drive select
# no:  No automatic trigger
# Values: yes | sel | no
display-on-activity = yes

# LCD/OLED long filename scroll rate in milliseconds per update
# Values: 100 <= N <= 65535
display-scroll-rate = 200

# LCD/OLED pause time at start/end of scroll, in milliseconds
# Zero means endless scroll
# Values: 0 <= N <= 65535
display-scroll-pause = 2000

# LCD/OLED long filename scroll rate during navigation (ms per update)
# Values: 0 <= N <= 65535
nav-scroll-rate = 80

# LCD/OLED long filename pause before scroll, during navigation (milliseconds)
# Values: 0 <= N <= 65535
nav-scroll-pause = 300

##
## MISCELLANEOUS

# Speaker volume for head STEP
# Values: 0 <= N <= 20
step-volume = 20

# Report the specified version number to host software
# Values: <quoted-string> ("" means report real version)
# eg. da-report-version = "v3.0.0.0"
da-report-version = ""

# Automatically extend certain types of truncated image file (SSD,DSD,TRD)?
# Values: yes | no
extend-image = yes

Waldek

  • ***
  • Wiadomości: 156
  • Miejsce pobytu:
    Łużyce
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #12 dnia: 2023.03.08, 22:25:27 »
Nie widzę żadnych problematycznych wpisów w konfiguracji.

Gdzie w pamięci USB znajduje się plik FF.CFG, w katalogu głównym czy w katalogu FF czy gdzieś indziej ?
Czy istnieją dodatkowe pliki konfiguracyjne, np. HXCSDFE.CFG?
« Ostatnia zmiana: 2023.03.08, 22:35:11 wysłana przez Waldek »

lukwol

  • *
  • Wiadomości: 42
  • Miejsce pobytu:
    Warszawa
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #13 dnia: 2023.03.12, 16:16:29 »
Plik ff jest w katalogu głównym , HXCSDFE.CFG jest również .

damik

  • Fresh rosin sniffer ;)
  • *****
  • Wiadomości: 2426
  • Miejsce pobytu:
    Generalnie Polska, głównie Bytom czasem Bielsko-Biała oraz okolice
  • ZX'owy i nie tylko...
Odp: Gotek z wyświetlaczem , plik ff.cfg
« Odpowiedź #14 dnia: 2023.03.12, 20:57:37 »
Podmień jeszcze Pendrive na inny jakiś mniejszej pojemności.
Wszystkiego po trochu: Schwarz, mydło i powidło... konsole, stare i nieco nowsze komputery oraz akcesoria i duperele.