forum speccy.pl

ZX Spectrum => HARDWARE => Wątek zaczęty przez: lotharek1977 w 2012.06.30, 01:13:20

Tytuł: DivIDE2k11
Wiadomość wysłana przez: lotharek1977 w 2012.06.30, 01:13:20

Witam

krotka informacja - http://velesoft.speccy.cz/zx/divide2k11/index.html

z velesoftem dopiescilismy :-) jest OK

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: Tygrys w 2012.06.30, 02:13:16

Fajnie. A co bylo nie tak?

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: lotharek1977 w 2012.06.30, 16:25:55

zacytuje VELSOFTA

I verify your last source and equations is based on A_GAL + M'GAL + R"GAL = same firmware as in original DivIDE 57c.

My last modification of your source only add one new feature (reset mapram without power-off ZX)

Logic in original divide is limited with small GAL chips and device is not so good as can be :) Original divide is designed also for tr-dos emulation, but only connection of trdos memory is compatible with original betadisc and return from trdos rom is absolutly incompatible and in your divide this can be fixed (I can add new tr-dos compatible mode, also compatibility with ZX128 rom, compatibility with
ZX128+2A/+3 rom and +3 allram mode).
Idea: add possibility switch DIVIDE 2K11 to "super mode" = all new features can be enable or disable (default = original divide)

VELESOFT

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: VELESOFT w 2012.06.30, 17:16:06

Cytat: lotharek1977 w 2012.06.30, 16:25:55

zacytuje VELSOFTA

I verify your last source and equations is based on A_GAL + M'GAL + R"GAL = same firmware as in original DivIDE 57c.

My last modification of your source only add one new feature (reset mapram without power-off ZX)

Logic in original divide is limited with small GAL chips and device is not so good as can be :) Original divide is designed also for tr-dos emulation, but only connection of trdos memory is compatible with original betadisc and return from trdos rom is absolutly incompatible and in your divide this can be fixed (I can add new tr-dos compatible mode, also compatibility with ZX128 rom, compatibility with
ZX128+2A/+3 rom and +3 allram mode).
Idea: add possibility switch DIVIDE 2K11 to "super mode" = all new features can be enable or disable (default = original divide)

VELESOFT

About compatibility with ZX128 rom/+2A rom:
- need connect signal /RESET from ZX bus to CPLD
- jumper for +2A compatibility must be connect also to CPLD ( is possible test it via extra software, but reading of jumper state is better)

Idea:
- add reset button to DivIDE 2k11 (very good for use with rubber speccy, TK90X, Timex Computers, Didaktik Gama....)

Yet I can add some features:
- possibility read state of paging port on ZX128/+2A/+3 (7ffd, 1ffd)
- possibility read state of last selected AY register (for possibility make snapshots with correct AY music settings)
- possibility read state or border colour (for correct saving snapshots)
- tr-dos compatibility mode

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: YERZMYEY/HOOY-PROGRAM w 2012.06.30, 18:42:25

Hmm. No to jakiego firmware'u będzie potrzebować, żeby chodził TR-DOS??

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: VELESOFT w 2012.06.30, 20:51:29

Cytat: YERZMYEY/HOOY-PROGRAM w 2012.06.30, 18:42:25

Hmm. No to jakieś firmware'u będzie potrzebować, żeby chodził TR-DOS??

DivIDE hardware is designed also for trdos emulation. System ESXDOS will support TR-DOS.

See here - mounting of TRD images:

Meanwhile, here's a short video of v0.8.1 (vdisks, FAT image mounting, early TRDOS driver)
(http://velesoft.speccy.cz/other/esxdos_081.gif)

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: andy w 2012.06.30, 20:55:09

2k11 = 2110. Nieźle do przodu :)

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: lotharek1977 w 2012.07.01, 10:35:33

2k11= 2*1000+11=2011

Tytuł: Odp: DivIDE2k11
Wiadomość wysłana przez: andy w 2012.07.01, 21:01:57

2k7 = 2700 om, 1k33 = 1330, 5V1 = 5.1V, 4µ7 = 4.7 µF