Autor Wątek: DivIDE2k11  (Przeczytany 6652 razy)

lotharek1977

  • **
  • Wiadomości: 90
  • Miejsce pobytu:
    Maly sklepik ;-)
  • Jestem maly sklepikarz ;-)
    • Lotharek`s Lair
DivIDE2k11
« dnia: 2012.06.30, 01:13:20 »
Witam

krotka informacja - http://velesoft.speccy.cz/zx/divide2k11/index.html

z velesoftem dopiescilismy :-) jest OK
NIE ODPISUJE NA PM, tylko [email protected]

Tygrys

  • Administrator
  • *****
  • Wiadomości: 4537
  • Miejsce pobytu:
    Warszawa
  • mistrz ceremonii
Odp: DivIDE2k11
« Odpowiedź #1 dnia: 2012.06.30, 02:13:16 »
Fajnie. A co bylo nie tak?

lotharek1977

  • **
  • Wiadomości: 90
  • Miejsce pobytu:
    Maly sklepik ;-)
  • Jestem maly sklepikarz ;-)
    • Lotharek`s Lair
Odp: DivIDE2k11
« Odpowiedź #2 dnia: 2012.06.30, 16:25:55 »
zacytuje VELSOFTA

I verify your last source and equations is based on A_GAL + M'GAL + R"GAL = same firmware as in original DivIDE 57c.

My last modification of your source only add one new feature (reset mapram without power-off ZX)

Logic in original divide is limited with small GAL chips and device is not so good as can be :) Original divide is designed also for tr-dos emulation, but only connection of trdos memory is compatible with original betadisc and return from trdos rom is absolutly incompatible and in your divide this can be fixed (I can add new tr-dos compatible mode, also compatibility with ZX128 rom, compatibility with
ZX128+2A/+3 rom and +3 allram mode).
Idea: add possibility switch DIVIDE 2K11 to "super mode" = all new features can be enable or disable (default = original divide)

VELESOFT
NIE ODPISUJE NA PM, tylko [email protected]

VELESOFT

  • ****
  • Wiadomości: 272
Odp: DivIDE2k11
« Odpowiedź #3 dnia: 2012.06.30, 17:16:06 »
zacytuje VELSOFTA

I verify your last source and equations is based on A_GAL + M'GAL + R"GAL = same firmware as in original DivIDE 57c.

My last modification of your source only add one new feature (reset mapram without power-off ZX)

Logic in original divide is limited with small GAL chips and device is not so good as can be :) Original divide is designed also for tr-dos emulation, but only connection of trdos memory is compatible with original betadisc and return from trdos rom is absolutly incompatible and in your divide this can be fixed (I can add new tr-dos compatible mode, also compatibility with ZX128 rom, compatibility with
ZX128+2A/+3 rom and +3 allram mode).
Idea: add possibility switch DIVIDE 2K11 to "super mode" = all new features can be enable or disable (default = original divide)

VELESOFT

About compatibility with ZX128 rom/+2A rom:
- need connect signal /RESET from ZX bus to CPLD
- jumper for +2A compatibility must be connect also to CPLD ( is possible test it via extra software, but reading of jumper state is better)

Idea:
- add reset button to DivIDE 2k11 (very good for use with rubber speccy, TK90X, Timex Computers, Didaktik Gama....)

Yet I can add some features:
- possibility read state of paging port on ZX128/+2A/+3 (7ffd, 1ffd)
- possibility read state of last selected AY register (for possibility make snapshots with correct AY music settings)
- possibility read state or border colour (for correct saving snapshots)
- tr-dos compatibility mode





YERZMYEY/HOOY-PROGRAM

  • *****
  • Wiadomości: 1187
  • Miejsce pobytu:
    Rubber Planet
  • AY RIDERS
    • ZX Spectrum demos/games
Odp: DivIDE2k11
« Odpowiedź #4 dnia: 2012.06.30, 18:42:25 »
Hmm. No to jakiego firmware'u będzie potrzebować, żeby chodził TR-DOS??
« Ostatnia zmiana: 2012.06.30, 21:37:24 wysłana przez YERZMYEY/HOOY-PROGRAM »

VELESOFT

  • ****
  • Wiadomości: 272
Odp: DivIDE2k11
« Odpowiedź #5 dnia: 2012.06.30, 20:51:29 »
Hmm. No to jakieś firmware'u będzie potrzebować, żeby chodził TR-DOS??

DivIDE hardware is designed also for trdos emulation. System ESXDOS will support TR-DOS.

See here - mounting of TRD images:

Meanwhile, here's a short video of v0.8.1 (vdisks, FAT image mounting, early TRDOS driver)

andy

  • *****
  • Wiadomości: 1065
  • Miejsce pobytu:
    Kielce Wsch.
Odp: DivIDE2k11
« Odpowiedź #6 dnia: 2012.06.30, 20:55:09 »
2k11 = 2110. Nieźle do przodu :)
pzdr
a.
POKE 35899,0  ZX 81, ZX Spectrum +, +2, Harlequin, ZX Max 48 & 128, Spider 48, Chrome 128, TC 2048, divIDE, CPC 464

lotharek1977

  • **
  • Wiadomości: 90
  • Miejsce pobytu:
    Maly sklepik ;-)
  • Jestem maly sklepikarz ;-)
    • Lotharek`s Lair
Odp: DivIDE2k11
« Odpowiedź #7 dnia: 2012.07.01, 10:35:33 »
2k11= 2*1000+11=2011

NIE ODPISUJE NA PM, tylko [email protected]

andy

  • *****
  • Wiadomości: 1065
  • Miejsce pobytu:
    Kielce Wsch.
Odp: DivIDE2k11
« Odpowiedź #8 dnia: 2012.07.01, 21:01:57 »
2k7 = 2700 om, 1k33 = 1330, 5V1 = 5.1V, 4µ7 = 4.7 µF
pzdr
a.
POKE 35899,0  ZX 81, ZX Spectrum +, +2, Harlequin, ZX Max 48 & 128, Spider 48, Chrome 128, TC 2048, divIDE, CPC 464